Skip to main content
Image
hero-spo2-probe2-sp
Image
Product Accessory SpO2 hero image
SpO2 probe from the company that invented from the principle of SpO2

SpO2 Sensors

Image
logo blupro
SpO₂ sensors and probes

Overview

The Pulse Oximeter is a device that continuously and non-invasively monitor the level of oxygen in patients’ bloodstream and pulse oximetry, the principle, was invented by Dr. Takuo Aoyagi, an engineer at Nihon Kohden in 1972. Nihon Kohden has two types of SpO2 probes: Single patient use probes and reusable probes. Select an appropriate type according to your application.

Image
SpO2 sensor thumbnail image 01

Single-patient use probes

Image
SpO2 sensor thumbnail image 02

Reusable probes

Single-patient use probes

  • For long-term monitoring, the structure is designed to prevent compression and misalignment
  • A one-piece probe with adhesive tape that is easy to attach on the patient skin
  • Easy to apply with full-range of sizes, from neonate to adult

Reusable probes

  • Ideal for spot monitoring
  • A unique design to offer painless and supreme comfort to the patient by providing an optimal distribution of pressure which prevents blood clots or skin trauma
  • Cleaning and disinfection are available

For Better SpO2 Monitoring

The SpO2 value is often affected by the patient’s condition, artifacts created by external devices or by inappropriate attachment of probes. Nihon Kohden’s monitor has several features for better SpO2 measurement. Let us introduce four features: Signal Quality Index (SQI), Pulse-amplitude Index (PI), Response, and Sensitivity Mode.

Signal Quality Index (SQI)

Nihon Kohden’s monitors display the quality of the pulse waveform signal, which is used to measure SpO2, by a bar graph. If the SQI bar graph displays 2 yellow bars or below, check for the patient’s physical movement and/or how the probe is attached.

 

Image
SpO2 image 01

 

SQI Bar Graph

Signal Quality
Image
SpO2 image 02

4 green bars

Good.
Image
SpO2 image 03

3 green bars

There may be some artifacts.
Image
SpO2 image 04

2 yellow bars 1

There may be significant artifacts. If this continues for a while, check the patient and probe attachment site.
Image
SpO2 image 05

1 red bar 1

Very low.            
Check the patient and probe attachment site.
Image
SpO2 image 06

0 bars

The signal cannot be detected.

1 If the SQI bar graph shows 1 or 2 bars, the “Low Quality Signal” message appears on the monitor.

Pulse-amplitude Index (PI)
Image
SpO2 image 01
Image
SpO2 image 07

The Pulse-amplitude Index, PI, indicates the percentage of the pulsatile signal as a proportion of the entire transmitted infrared signal. It fluctuates depending on the size of transmitted signal and the size of the pulsatile signal obtained from the probe attached to the patient.

PI can be used as an index to confirm the circulation of the attachment site as well as to check the condition of an attachment site of SpO2 probe so if the attachment site is too thick or if an SpO2 probe is inappropriately attached, the intensity of the transmitted light decreases, meaning the PI value becomes low.                      
When the PI is low, any of the following situations might be happening.

  • Measurement site is cold
  • SpO2 probe is attached too tight
  • The patient is in a condition of shock
  • The patient is a premature baby

If the PI value is low, check the probe attachment as the probe may block blood flow of the measurement site due to the high pressure if it is attached too tight.                      
If the PI value is low, but the probe is properly attached, change the probe attachment site for more reliable SpO2 measurement.      
If the SpO2 value and PI value are dropping simultaneously, there is a possibility that the SpO2 probe might have deviated from the correct attachment position.

Response: Fast, Normal, Slow

This is a feature that lets you set the response times of the SpO2 value. We have Normal, Slow and Fast mode.                  
Normal: Standard response time                  
Slow: Slower response. This is useful when you want to control transient fluctuations in the SpO2 value.                  
Fast: Faster response. This can be used in a situation that require an extremely fast response.                  

When measurement condition is unstable such as due to strenuous movement of the patient, response may become slower in all modes.

Image
SpO2 image 08
Sensitivity Mode

Sensitivity mode allows you to improve the sensitivity of the pulse wave, therefore this feature is useful when it is difficult to detect the pulse of a patient with peripheral circulation insufficiency or when an IABP (Intra-Aortic Balloon Pump) is used.                  
On the other hand, an SpO2 value may be measured even if the probe is detached from the patient. Therefore, when selecting “Max” for the setting, it is necessary to confirm that the probe is appropriately attached to the patient.

Image
SpO2 image 09
Image
SpO2 image 10

Tips for accurate measurement

1. Select an attachment site with an appropriate thickness

A pulse oximeter detects the light that penetrates the measurement site. In most cases, a probe should be attached across a measurement site with a thickness of 6-18 mm to obtain stable and accurate SpO2 value.

Image
SpO2 image 11
2. Attach the probe correctly

To obtain stable and accurate SpO2 measurement, the probes should be attached in the correct position so that the light emitter and the photo detector face each other like in the following image.

Image
SpO2 image 12
3. Periodically change the attachment site

To prevent skin damage due to prolonged attachment, it is important to check and change the attachment site if necessary.
For single-patient use probe: within every 8 hours
For reusable type: within every 4 hours

Check the following videos for more tips of SpO2 measurement.

SpO2 Probe Attachment Guide

SpO2 Probe Attachment Guide
(for probes for Neonate and Low birth weight infants)

Video

Material Downloads